Free sensor experience 3

ruthbia said:
I have that of Diabox and G-Watch.
The sensor remains fatal ...

I think that in the FreeLink app they would not give you such erratic ups and downs.

I don't care.It is what the sensor reports.

Those ups and downs of LibreLink take about an hour.That's "normal"

They are not the ones you put before the Diabox data, which in a minute climbed you a lot and the next one also lowered you a lot.

Yes, not only Diabox, Freestyle and LibreLink takes the same graphic.Every 10 min collapse and tells me to wait for me.
A disgust

To me that I expect 10 minutes I also get out every time in my last sensor and sometimes it is more than an hour without showing any value.

It is also a very bad sensor.

On the other hand, the graph going up and going down a lot in a minute, I only saw it in the Juggluco app, to remove it and go to LibreLink that no longer comes out.

ruthbia said:
@fercomi is a subject of application permits.

MAKES ME NFC ERROR.
I could not solve it.Because it is active and works perfectly.I don't know why that error in Diabox comes out.

Freestyle 2 works well for me.At the beginning he checked with the glocometer and found that the didances were irrelevant.Moreover, when they make me blood analytics, the almost "nail" sensor the result of the laboratory.In two years I have only failed 3 sensors.3 More stopped working because of restless doors or corners frames that "harassed me", my glycosilada, after 43 years of illness is 6.9.
I have the glycometer in the trunk of memories.

sherpa41 said:

ruthbia said:
in ABBOT problem is the manufacture of the sensor.
It is incredible as they fail in readings depending on the integrator they have and how bad the factory test (FAT) is.
The one I started on Tuesday is going quite badly, it cannot have such great jumps from one minute to another.And I was not pressing or sleeping in the shower.

I have not managed to calibrate.I have had to delete data and start again, and that I never calibrate on the 1st start.

Something similar happened to me at the beginning of the sensor that I carry, I put Juggluco and in 1 minute I climbed 30, then the next one went down 30, etc.The graph was crazy.However, in LibreLink these variations were not seen, so I removed the Juggluco app.

Do you also see you in LibreLink or only in the Diabox app?

Free 2 can be calibrate ????

antonimar said:

sherpa41 said:

ruthbia said:
ruthbia said:
in abbot problem is the manufacture of the sensor.
It is incredible as they fail in readings depending on the integrator they have and how bad the factory test (FAT) is.
The one I started on Tuesday is going quite badly, it cannot have such great jumps from one minute to another.And I was not pressing or sleeping in the shower.

I have not managed to calibrate.I have had to delete data and start again, and that I never calibrate on the 1st start.

Something similar happened to me at the beginning of the sensor that I carry, I put Juggluco and in 1 minute I climbed 30, then the next one went down 30, etc.The graph was crazy.However, in LibreLink these variations were not seen, so I removed the Juggluco app.

Do you also see you in LibreLink or only in the Diabox app?

Free 2 can be calibrate ????

Can be in the diabox application

Hello the Freestyle 2 measures me to the top and the differences are higher in very high or very low values ​​but I am already used to it.When it differs a lot from reality I change it for example if it tells me that I have 300 and I have 150 but that has happened to me twice.It does not take off and if you sleep on top of it it gives hiccups that it is not real.Now I have changed to the Dexcom One + Q in Catalonia they finance it is a more precise tad but when it loses the connection to Vecss it takes to recover and only lasts 10 days.It is smaller and the app is not detached is shit but I have opted for it perhaps when they finance the 3 returns to freestyle.